heading
Condition
Manufacturer
Type
Year

Cost €


Pellet factory, making wood pellet from dry sawdust. & Dryer line, for dryer wet sawdust.

Photo

Full description ID 20

Dryer line, for dryer wet sawdust.

Capacity 6,0 ton / hour. Time 300 days and 24 hours. 7200 hour / year. Capacity / year 43 200 ton / vuosi. Owerhould and taked to production 2008.

- Feeding container for fuel, 4 m3.

- Own 6 MW, moving grate.

- Primary air fan, blow air under the grate.

- Secondary air fan, blow air up to flames.

- Chain conveyor for take ash out of own.

- Mixer, mix hot and cold air.

- Feeding container for wet sawdust.

- Feeder for wet sawdust whit leveller.

- Feeding screw for wet sawdust.

- Drying drum, 3 levels, Swiss Combi MK 5.

- Airlock, take dry sawdust to chain conveyor.

- Cyclone. Separate fine dust and air.

- Airlock, take fine dust to chain conveyor.

- Main fan, 90 kw

- Chain conveyor. 35 m. Take dryed sawdust to storage.

- Automatik water hydrant, for fire (2 ps)

- Heat sensors. (2 ps)

- Electrical center, whit Siemens logistic.

- PC-computer for use dryer from control room.

- Cameras, ( 4 ps ) same control panel than factory 3

Guarantee:

- Production capacity 6,0 ton / hour. 

PELLET FACTORY.

Pellet factory, for making wood pellet from dry sawdust ( moisture 10 – 14 % ). Capacity / hour 6,0 ton / hour. Time 300 days and 24 hours. 7200 hours / year. Capacity per year 43 200 ton / Year. Capacity is for 8 mm wood pellet. Raw material Dry shavings or dry sawdust. Moisture 10 – 14 %.

- 2 pcs hydraulic units. - Feeding table with scrapers (8000 mm * 12000 mm) Table is with 600 mm legs. - 8 pcs scrapers with cylinders take dry sawdust out of table to feeding screw. - 2 pcs feeding screws ( diameter 600 mm ja lenght 6000 mm ) take sawdust to hammer mill.

- 2 pcs Wynween hammermill whit 132 kW motor.

- 2 pcs Stone pocket, take stones and heavy particles out of sawdust.

- 2 pcs Pneumatic movers for hammer mill. o 2 Pcs Fan with 11 kW motor. o 2 pcs Filter station. o 2 pcs Airlock with 1,5 kW motor.

- 3 pcs Feeder with level controller and with leveler. 2 * 2,2 kW and 2 * 1,5 kW motors and coolers for motor. Speed of leveler control intake power of main motor of press by automatic. .

- 3 pcs Mixer, that homogenized ships for press 2 * 11 kW motor. And turning plates.

- 3 pcs. Pellet presses Kahl C – 40 – 1000 3 * 250 kW motor and machine beds.

- 3 pcs Oil coolers cooling gearbox oils for pellet press. 3 * 2,2 kW.

- 3 pcs Central lubrication units for greasing the collar heads.

- 5 pcs chain conveyors take hot pellets from press to cooler. 5 * 1,5 kW motor.

- 1 pcs Horisontal Belt cooler, for cooling hot pellet for storage. 2,2 kW motor.

- 1 pc Cooling system. - Fan 18,5 kW motor. - Cyclone - Airlock 2,2 kW motor.

- 1 pc Belt conveyor, to take cooled pellet to screen. 0,50 kW motor.

- 1 pc Screen, to take fine dust out of pellet. Fine dust goes back to feeding table by air. 0,55 kW motor.

- 1 pc Dust evacuation system. - Fan 30 kW motor. - Cyclone. - Airlock 2,2 kW motor.

- Screw compressor with dryer.

- 1 pc Electrik container. - Soft starters for Presses and big fans and hammer mills. - Control system by Moeller. - Full automatik smallbaggaging machine for 12,5 kg bags.

- Automatik palleting machine, to 600 kg / pallet

- Scraper for pallet, put plastics around the pallet - Forklift ( Daewoo ) - Cameras for control of factory and lines ( 8 cameras ) - Camera control system to control room -

Spare parts:

- 4 pcs 6 mm dies - 10 pcs 8 mm dies - 10 pcs bearings to collar head - drilling machine for repair of dies - some small motors 0,5 – 3 kW - service tools forcollar head - container for fireworks and service container for tools

Year: 2008
*This item is located in Europe. The price does not include: disassembly-assembly, transportation and customs clearance, including taxes and fees. Unless otherwise indicated in the text.